L-4250

Name: InLog L-4250 Two Ethernet Digital 10-ch (Dry/Wet) 6-ch (NPN) I/O Module
SKU: L-4250

InLog

InLog L-4250 Two Ethernet Digital 10-ch (Dry/Wet) 6-ch (NPN) I/O Module

L-4250

2-ports(RJ-45) Ethernet 10/100 Based-T Comm.
Daisy chain connection with auto-bypass protection
Support Modbus/TCP,TCP/IP,UDP,ICMP,ARP
Support Automatic DIO Sync.(peer-to-peer).
DO Auto-Off Time Mode.
Support 6 Isolated digital output channels (NPN).
Support 10 Isolated digital Input Channels(Dry/Wet)
Fully Photo-Isolation 3750Vrms
Protocol: ASCII Format & Modbus TCP

Product Code: L-4250

Categories: Data Acquisition Modules, Digital & Analogue I/O, Distributed I/O, InLog

Range: InLog

Details

The EDAM-4250 is a high-density I/O module built-in two ports(RJ-45) 10/100 based-T interface for seamless Ethernet connectivity. It provides 10 Isolated digital input (Dry/WetContact) and 6 digital output channels with 3750VRMS Isolating protection. All of the Digital Input channels support input latch function for important signal handling. Mean while, these DI channels allow to be used as 300Hz counter.

Opposite to the intelligent DI functions, the Digital Output channels also support pulse output function.

Daisy Chain Networking and Auto-Bypass Protection

Daisy Chain Networking and Auto-Bypass Protection Daisy chain connectivity offers flexible cabling and space saving capabilities. With Ethernet auto-bypss function supported, it prevents accidental power failure if one of the module’s unexpectedly shuts down.

Automatic DIO Synchronization (peer-to-peer)

EDAM-4250 module also provide a Automatic DIO Synchronization function. With peer-to-peer networking, users can define the mapping between a pair of EDAM-4200 series modules so that input values will be directly transferred to output channels. A single digital output channel (Local/Remote device) is activated(1/0 or toggle) dependent on the digital input channels state data pattern. When the specified DI channels state data pattern changed from "Match" to "Notmatch" the corresponding DO will be set to active(1 or 0).

Downloads

InLog L-4250 Datasheet (PDF)

0.38MB

System Integration

Please ask about how we can configure your solution

Global Operations

We deliver and support products via offices globally

Full Warranty

Industry leading warranties on all solutions as standard

Technical Support

Experienced engineers are on hand to support your project

Can't Find What You Want?

Custom Design

Specification

Communication
Interface	2-port(RJ45) Ethernet 10/100 Based-T comm.
Communication	Support TCP/IP, UDP, ICMP and ARP
RJ-45 Connection	Daisy Chain Connection with auto-bypass protection
Command Protocol	ASCII Format, Modus/TCP
Digital Input
Channel	10 Channels
Input Level	Logic Level Status can be inversed via ASCII/Modbus command
Input Type	Isolated single ended with common source/ground
Dry Contact	Logic level 0 (active) : Close to GNDLogic level 1 (inactive): Open
Wet Contact	Logic level 0 (active) : +5V to +30VDC maxLogic level 1 (inactive) : +2VDC max
Input Impedance	2K ohm (Wet Contact)
Counter Input	300Hz counter input (32-bit + 1-bit overflow)
Optical Isolation Voltage	3750 Vrms
Digital Output
Channel	6 Channels
Digital Output	isolated open collector (NPN)
Output logical level	Logic level status can be inversed via ASCII/Modbus command
Output Load Voltage	+5V ~ +30V
Max Load Current	500mA/per channel
Pulse Output	Each Channel supports 300Hz pulse output
Optical Isolation	3750 Vrms
Display
Status Indicator	LED indicator
Common
Power Requirement	+10 to +30VDC
Power Consumption	3.5 W (Typical)
Operating Temperature	-10 ~ 70° C (14 ~ 158° F)
Humidity	5 ~ 95% RH, non-condensing